Lab Gruppen E 10:4 1000 Watt Amplifier with 4 Flexible Output Channels for Installation Applications

E SERIES E 10:4

The E 10:4 has Smart Green Credentials delivering low lifetime cost of ownership.

Small in Size, Huge in Benefits

Building on Lab Gruppen’s touring reputation for sonic excellence and rock-solid durability, E Series brings a competitive edge to the installation market by adding ultra-compact size, high operating efficiency, output configuration flexibility, and an unprecedented cost-benefit ratio.

At the heart of E Series is Lab Gruppen’s IDEEA (IntelliDrive Energy Efficient Amplifier) technology. Based around a patented Class D variant output stage, IDEEA produces high power levels with very low distortion while drawing minimal mains current.

Lab Gruppen’s proprietary Rail Sensing Limiter (RSL™), also exclusive to E Series, greatly reduces signal clipping to ensure high quality audio output at all times. User configurable for Hi-Z (70 V) or Lo-Z, RSL senses rail voltages and optimizes each output for instantaneous load conditions. RSL settings also facilitate asymmetric loading of the channels to optimize performance and efficiency. Total available output power can be allocated among the channels as required by the application. This makes it possible, for example, to drive a small sub on one channel, a number of 70 V ceiling loudspeakers on the second channel, and a pair of full-range low impedance loudspeakers on the two remaining channels.

Lab Gruppen Performance with Energy Star Compliance

By maintaining very low current draw during operating cycles even at high output levels, and reduced power consumption during non-operational cycles, our Energy Star qualified products harness impeccable Lab Gruppen sonic performance and robust power output while meeting the rigorous efficiency requirements of current Energy Star certification standards.

Lab Gruppen’s IDEEA architecture secures full Energy Star compliance by combining net operating efficiency of greater than 80% with an auto-power-down feature. After 20 minutes with no input signal, the amplifier automatically switches to standby mode – with consumption of less than 1 W – and switches back on when an input signal returns. GPIO facilities enable third-party systems to remotely control and monitor power state via contact closure.

Smart Green Credentials with Our IDEEA Platform

The now proven IntelliDrive Energy Efficient Amplifier (IDEEA) platform represents the latest evolution of our amplifier design philosophies, drawing from technologies in our flagship PLM Series, to create ingenious contractor solutions with supreme green credentials.

Flexible Asymmetric Loading

Optimize performance and efficiency from each individual unit - allowing the total available output power to be utilized unequally between the channels, or for mono use with all power on a single channel. Enabling you to drive a small sub on one channel and a number of 70 V distributed ceiling loudspeakers on the other.

Specification:

General

Number of amplifier channels	4
Total output all channels driven	1000 W
Peak output voltage per channel	100 V / 70 Vrms
Max. output current	14 Arms

Max output power (all channels driven)

2 ohms	N.R.
4 ohms	250 W
8 ohms	250 W
16 ohms	250 W (requires the “70 V” mode for the RSL, “Lo-Z” gives 125 W)
70 V	250 W
100 V	Can deliver 250 W to a 100 V load tapped at 500 W

Performance

THD 20 Hz - 20 kHz at 1 W	<0.1%
THD at 1 kHz and 1 dB below clipping	<0.05%
Signal to Noise Ratio	>112 dBA
Channel separation (Crosstalk) at 1 kHz	> 70 dB
Frequency Response	2 Hz - 40 kHz
Input impedance	20 kOhm
Common Mode Rejection (CMR)	50 dB
Output impedance	25 mOhm

Gain, Sensitivity and Limiters

Limit and gain switch defining limit and gain (per channel)	2 pos: Lo-Z and 70 V
VPL for 70 V mode	100 V
VPL for Lo-Z mode	63.2 V
Sensitivity for stated power into 8 Ohm in Lo-Z mode	4 dBu
Sensitivity for 70.7 V out in 70 V mode	4 dBu
Sensitivity for stated power into 4 Ohm in Lo-Z mode	1 dBu
Sensitivity for stated power into 16 Ohm in 70 V mode	3 dBu
Gain in 70 V mode	35.2 dB
Gain in Lo-Z mode	31.2 dB
Level adjustment (per channel)	Rear panel potentiometer, from -inf to 0 dB

Connectors and Switches